117 ?2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com/spa for current information. tvs diode arrays (spa ? family of products) revision: april 14, 2011 sp03-6 series sp03-6 lightning surge protection - sp03-6 series description features applications this new broadband protection device from littelfuse provides overvoltage protection for applications such as 10/100/1000 baset ethernet, t3/e3 ds3 interfaces, adsl2+, and vdsl2+. this new protector combines the tvs diode element with a diode recti?er bridge to provide both longitudinal and differential protection in one package. this design innovation results in a capacitive loading characteristic that is log-linear with respect to the signal voltage across the device. this reduces intermodulation (im) distortion caused by a typical solid-state protection solution. the application schematic provides the connection information. pinout functional block diagram agency approvals - pending agency agency file number e128662 t 3 p ) 4 d p n q m j b o u t . 4 t v s g b d f n p v o u package (jedec so-8) t - p x j o t f s u j p o m p t t
m p h linear capacitance t $ p n c j o f e m p o h j u v e j o b m and metallic protection t $ m b n q j o h t q f f e p g nanoseconds t 6 - 7 f q p y z n p m e j o h t 1 f o e j o h 6 - s f d p h o j [ f e component t - p x d m b n q j o h w p m u b h f t 5 & - j o f d b s e t t 5 & b o e % 4 * o u f s g b d f t t 4 5 4 * o u f s g b d f t t # b t f 5 ethernet so-8 (top view) 1 2 3 5 4 6 7 8 pin 1 and 8 pin 4 and 5 ground pin 2, 3, 6, and 7 line out line out line in line in life support note: not intended for use in life support or life saving applications the products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. rohs pb green application example this schematic shows a high-speed data interface protection solution. the sp03-6 provides both metallic (differential) and longitudinal (common mode) protection from lightning induced surge events. its surge rating is compatible with the intra-building surge requirements of telcordias gr-1089-core, and the basic level recommendations of itu k.20 and .21. this device protects against both positive and negative induced surge events. the telelink fuse provides overcurrent protection for the long term 50/60 hz power fault events. 1 2 3 4 8 7 6 5 to chipset (ethernet phy, t3/e3 phy, etc.) ring tip telelink (0461 1.2 5 ) sp03-6 sp03-6 series 6v 150a rail clamp array
?2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com/spa for current information. 118 tvs diode arrays (spa ? family of products) revision: april 14, 2011 sp03-6 series lightning surge protection - sp03-6 series absolute maximum ratings parameter rating units peak pulse current (8/20s) 150 a peak pulse power (8/20s) 2800 w iec 61000-4-2, direct discharge, ( level 4) 30 kv iec 61000-4-2, air discharge, ( level 4) 30 kv iec 61000-4-5 (8/20s) 100 a telcordia gr 1089 (intra-building) (2/10s) 100 a itu k.20 (5/310s) 40 a electrical characteristics (t op = 25c) thermal information parameter rating units soic package 170 c/w operating temperature range -55 to 125 c storage temperature range -65 to 150 c maximum junction temperature 150 c maximum lead temperature (soldering 10s) (soic - lead tips only) 260 c parameter symbol test conditions min typ max units reverse stand-off voltage v rwm ---6v reverse breakdown voltage v br i t = 1ma 6.8 - - v reverse leakage current i r v rwm = 6v, t= 25c - - 25 a clamping voltage, line-ground v c i pp = 50a, t p =8/20 s - - 15 v clamping voltage, line-ground v c i pp = 100a, t p =8/20 s - - 20 v junction capacitance c j (line-ground) between i/o pins and ground v r =0v, f= 1mhz -1625pf c j (line-line) between i/o pins v r =0v, f= 1mhz -812pf caution: stresses above those listed in absolute maximum ratings may cause permanent damage to the device. this is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this speci?cation is not implied. figure 2: current derating curve figure 1: non-repetitive peak pulse current vs. pulse time pulse decay time (s) 1 10 100 1000 1 10 100 1000 peak pulse current (a) percentage of rated current (%i p ) ambient temperature (c) 0 20 40 60 80 100 120 0 20 40 60 80 100 120 140 160
119 ?2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com/spa for current information. tvs diode arrays (spa ? family of products) revision: april 14, 2011 sp03-6 series sp03-6 lightning surge protection - sp03-6 series figure 4: clamping voltage vs. peak pulse current figure 6: forward voltage vs. forward current figure 3: pulse waveform figure 5: capacitance vs. reverse voltage time, s 0 20 40 60 80 100 0 5 10 1 5 20 2 5 30 3 5 40 percentage of i pp (%) capacitance (pf) reverse voltage (v) 0 2 4 6 8 10 12 14 16 18 20 01234 5 67 line-to-line line-to-ground 0 5 10 1 5 20 2 5 02040608 0100 v c clamping voltage (v) i p peak impulse current (a) line-to-line line-to-ground 0 1 2 3 4 5 6 7 0 10203040 5 060708090100 forward current (a) forward voltage (v) ground-to-line time temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p reheat ramp-up r amp-up ramp-down r amp-d o critical zone t l to t p c ritical zon e t l to t p re?ow condition pb C free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) 60 C 180 secs average ramp up rate (liquidus) temp (t l ) to peak 3c/second max t s(max) to t l - ramp-up rate 3c/second max re?ow - temperature (t l ) (liquidus) 217c - temperature (t l ) 60 C 150 seconds peak temperature (t p ) 250 +0/-5 c time within 5c of actual peak temperature (t p ) 20 C 40 seconds ramp-down rate 6c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 260c soldering parameters
?2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com/spa for current information. 120 tvs diode arrays (spa ? family of products) revision: april 14, 2011 sp03-6 series lightning surge protection - sp03-6 series part numbering system product characteristics ordering information part number package marking min. order qty. SP03-6BTG soic tape & reel sp03-6 2500 lead plating matte tin lead material copper alloy lead coplanarity 0.004 inches (0.102mm) subsitute material silicon body material molded epoxy flammability ul94-v-0 sp 03 6 b t g series working voltage package b - soic t= tape & reel g= green - silicon protection array (spa tm ) family of tvs diode arrays part marking system package dimensions mechanical drawings and recommended solder pad outline package ms-012 (so-8) pins 8 jedec mo-223 issue a millimetres inches min max min max a 1.35 1.75 0.053 0.069 a1 0.10 0.25 0.004 0.010 a2 1.25 1.65 0.049 0.065 b 0.31 0.51 0.012 0.020 c 0.17 0.25 0.007 0.010 d 4.80 5.00 0.189 0.197 e 5.80 6.20 0.228 0.244 e1 3.80 4.00 0.150 0.157 e 1.27 bsc 0.050 bsc l 0.40 1.27 0.016 0.050 o recommended soldering pad outline (reference only) f l first line: part number second line: date code f l sp03-6 xxxxxxxx notes : 1. all dimensions are in millimeters 2. dimensions include solder plating. 3. dimensions are exclusive of mold ?ash & metal burr. 4. all speci?cations comply to jedec spec mo-223 issue a 5. blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 6. package surface matte ?nish vdi 11-13. embossed carrier tape & reel speci?cation soic package millimetres inches min max min max e 1.65 1.85 0.065 0.073 f 5.4 5.6 0.213 0.22 p2 1.95 2.05 0.077 0.081 d 1.5 1.6 0.059 0.063 d1 1.50 min 0.059 min p0 3.9 4.1 0.154 0.161 10p0 40.0 +/- 0.20 1.574 +/- 0.008 w 11.9 12.1 0.468 0.476 p 7.9 8.1 0.311 0.319 a0 6.3 6.5 0.248 0.256 b0 5.1 5.3 0.2 0.209 k0 2 2.2 0.079 0.087 t 0.30 +/- 0.05 0.012 +/- 0.002
|
